Dillon-precision XL 650 Manuel d'utilisateur télécharger pdf (Page 34)

1. How to use the Caliber

Conversion Chart:

To explain the Caliber Conversion

Chart we are going to compare the pistol

caliber of .38 Spl. to the rifle caliber of

.30-06 FIG 154.

By comparing the two columns, you can

see which parts need to be changed. In this

comparison, .38 Spl. vs. .30-06, you can

see that none of the part numbers match up,

therefore, all of the those parts would need

to be changed. This, however, is not always

the case. If you compare .30-06 to

.308/7.62 Nato, you’ll find that they are

exactly the same. Another example would

be .38 Spl. vs. .357 Magnum. As you can

see, they too are identical. Some caliber

comparisons will show that only a couple

of parts are different – in this case, instead

of ordering an entirely new caliber conver-

sion kit, you have the option of ordering

only those parts needed to complete your

caliber conversion.

2. Conducting the Caliber

Conversion

(The following steps are in the sequential

order in which the caliber conversion is to

be conducted):

Note: Included in the following is a com-

plete list of all the items that need to

be considered when conducting a

caliber conversion. This is not a list

of all the items that will need to

changed or readjusted – this is a

complete list of all the items that

may need to be changed or re-

adjusted. The items that need to be

changed or readjusted will depend

on the caliber your XL 650 is cur-

rently set up to load and the caliber

you’re changing to.

Step 1

) Remove the cases from the

machine:

1. Turn off the casefeed system

2. Remove the remaining cases from the

casefeed tube and the casefeed bowl.

Step 2

) Remove the powder from the

powder measure:

Depending on the caliber change, you

may have to change powders and/or the

powder bar. If so, you’ll need to empty the

powder from the powder measure.

FIG 155

1. Disconnect the failsafe rod FIG 155.

FIG 156

2. Loosen the two powder measure

clamp screws FIG 156.

3. Remove the powder measure and

empty the powder back into the pow-

der can.

4. Manually cycle the powder bar to

ensure the powder measure is empty.

5. If you need to change powder bars

refer to Step 19

FIG 157

Step 3

) Remove the toolhead FIG 157:

1. Disconnect the failsafe rod FIG 155.

2. Remove the toolhead pins and slide

the toolhead out.

Step 4) Remove the shellplate:

Remove the shellplate only if you need to

either, change the shellplate for a different

caliber shellplate, or if you need to remove

the primer system (such as when emptying

the primers from the primer system).

FIG 158

1. Using a 1/8” Allen wrench loosen the

shellplate set screw FIG 158. The

shellplate set screw is located on the

left side of the mainshaft just below

the shellplate platform. Do not

remove the screw, just loosen it about

a half turn.

Caliber Conversion Section

FIG 154 – Caliber Conversion Chart Sample

Caliber Complete Shellplate Locator Funnel Station 1 Casefeed Arm Body Casefeed Primer Powder

Conversion Number Button Locator Adapter Bushing Bushing Disc System Check Rod

38 Spl 21098 (2) 13430 (2) 14062 (D) 13599 (2) 13563 (Orange) 13386 (Red) 13403 (Sm38) 13384 (LP) 21072 Sm Med

.30-06 21094 (1) 13204 (1) 13930 (B) 13587 (1) 13595 (Black) 13541 (White) 13661 (Med) 13604 (LR) 21075 Lg Med

1 2 ... 29 30 31 32 33 34 35 36 37 38 39 ... 58 59

Commentaires sur ces manuels

Pas de commentaire

Dillon-precision XL 650 Manuel d'utilisateur Page 34

Commentaires sur ces manuels

Produits connexes et manuels pour Équipement Dillon-precision XL 650